Each surface type requires different maintenance and precautions. Please review the literature given to you and if you have any questions please contact us.
Dust mop interior floors frequently using a clean non-treated dry dust mop. Sand, dirt and grit do the most damage to natural stone surfaces due to their abrasiveness. Mats or area rugs inside and outside an entrance will help to minimize the sand, dirt and grit that will scratch the stone floor. Be sure that the underside of the mat or rug is a non-slip surface. Normally, it will take a person about eight steps on a floor surface to remove sand or dirt from the bottom of their shoes. Do not use vacuum cleaners that are worn. The metal or plastic attachments or the wheels may scratch the surface.
Clean stone surfaces with a few drops of neutral cleaner, stone soap (available at hardware stores or from your stone dealer) or a mild liquid dishwashing detergent and warm water. Use a clean rag mop on floors and a soft cloth for other surfaces for best results. Too much cleaner or soap may leave a film and cause streaks. Do not use products that contain lemon, vinegar or other acids on marble or limestone. Rinse the surface thoroughly after washing with the soap solution and dry with a soft cloth. Change the rinse water frequently. Do not use scouring powders or creams; these products contain abrasives that may scratch the surface.
Bath and Other Wet Areas
In the bath or other wet areas, soap scum can be minimized by using a squeegee after each use. To remove soap scum, use a non-acidic soap scum remover or a solution of ammonia and water (about 1/2 cup ammonia to a gallon of water). Frequent or over-use of an ammonia solution may eventually dull the surface of the stone.
Vanity Top Surfaces
Vanity tops may need to have a penetrating sealer applied. Check with your installer for recommendations. A good quality marble wax or non-yellowing automobile paste wax can be applied to minimize water spotting.
Food Preparation Areas
In food preparation areas, the stone may need to have a penetrating sealer applied. Check with your installer for recommendations. If a sealer is applied, be sure that it is non-toxic and safe for use on food preparation surfaces. If there are questions, check with the sealer manufacturer.
Outdoor Pool & Patio Areas
In outdoor pool, patio or hot tub areas, flush with clear water and use a mild bleach solution to remove algae or moss.
With simple care, Zodiaq® will retain its radiant, lustrous appearance for many years. For routine cleaning, use a damp cloth or paper towel and, if necessary, a small amount of non-bleach, nonabrasive cleanser.
Even though Zodiaq® resists permanent staining when exposed to liquids (such as wine, vinegar, tea, lemon juice and soda) or fruits and vegetables, wipe up food and liquid spills as soon as possible.
For stubborn or dried spills, use a nonabrasive cleaning pad such as a white 3M Scotch-Brite®* scrub pad coupled with Formula 409® Glass & Surface Cleaner** or a comparable cleaning product.
Avoid using cleansers that contain bleach. Always follow the cleaner manufacturer's use instructions and exercise proper care when handling and storing any cleaning products.
* Scotch-Brite® is a registered trademark of the 3M Company.
**Formula 409® Glass & Surface Cleaner is a registered trademark of the Clorox Company.
For day to day cleaning, warm soapy water or non-abrasive household cleaners such as glass cleaner, Fantastik®, Formula 409® or commercially available solid surface cleaners will remove most residues. Then rinse and towel dry the surface to prevent spotting especially in areas with hard water. For a final touch, you may apply Protect All Shine Plus™ to your countertop for a clean, dry professional appearance.
For stubborn residue that will not come out with day to day cleaning methods requires a slightly stronger cleaner. The following suggestions will assist you to remove stubborn residue and refurbish the finish.
To clean laminate countertops use a clean cloth and a mild dish soap and water. Dry the countertop after washing to prevent water from pooling in the seams.
Stained areas can be treated with a baking soda paste. Mix a 3:1 ratio of baking soda and water. Spread over the stain. Let sit for 3-5 minutes before wiping away. Don't scrub the countertop because, although it's a mild abrasive, the baking soda can damage the finish.
Wash well with a mild solution of clean dishwashing solution after every use, then rinse and wipe dry. Be certain that it is thoroughly dry BEFORE putting away in storage
After you cut meat and poultry on it, wet it down will with a disinfectant cleaner(see our website) or a 1 part chlorine bleach to 10 part water solution. Allow the solution to work for approximately 10 minutes, rinse well with clean water and allow to air dry.
Occasionally, deodorize surface with fresh lemon juice. Allow it to sit on surface for about 15 minutes. Then rinse, and dry.
Butcher block requires an 'oiling' from time to time to keep them from getting brittle. When the block is clean and dry, use mineral oil as a coating. Apply it and allow it to sit for about an hour. Wipe away excess, clean with a mild detergent, and allow to air dry. "Butcher block" that's not used for food preparation should be oiled occasionally with any store bought product designed for oil-finished furniture.
Find a better price? We will match it! Contact us for details